LOWER CONSUMPTION UP TO 50%

Proper application of lubricants can achieved up to half of mineral oil consumption. Thanks to our special additive, lubricants ensure perfect adhesion to the surface of the material ensures quality performance at a minimal amount. Coating technology lubricant for each production varies.
PROLONGS TOOLING LIFE

The protective film forms a continuous layer that protects the tool and the material to wear by up to 20%.
Forming lube
ALC 080


Golden liquid for extreme duty ferrous and yellow materials. Active on copper. Suitable for mid diameters. Further dilutable with water to reduce liquids viscosity. Best practice is to apply with pumping system of externally. Possible to distribute with re-fillable sprays as is.
- 1,5 - 2D bends
- Viscosity 123 cSt at 20°C
Good for steel, stainless steel and yellow metals.
ALC 100


Golden liquid for extreme duty ferrous and non-ferrous materials. Active on aluminium and aluminized materials. Suitable for big diameters and deep drawing. Further dilutable with water to reduce liquids viscosity. Best practice is to apply with pumping system of externally. Possible to distribute with re-fillable sprays with dilution of 20% water.
- 1D bends
- Viscosity 300 cSt at 20°C
Sutiable for steel, stainless steel, aluminium and titanium.
ALC 700


Dark liquid for extreme duty ferrous and non-ferrous materials. Suitable for big diameters and deep drawing. Further dilutable with water to reduce liquids viscosity. Best practice is to apply with pumping system of externally. Possible to distribute with re-fillable sprays with dilution of 20% water.
- 1D bends
- Viscosity 272 cSt at 20°C
Good for steel, stainless steel, aluminium, titanium and inconel.
NIROL 080


Clear, golden gel, designed especially to meet demands of non-pourable lubricating process, used through mandrel and also by brush.
- Viscous non-dripping gel (16000 cSt at 20°C)
- Activated by heat released by drawing process
Good for steel and stainless steel. Easy water clean-up.
NIROL 100


White gel designed especially to meet demands of non-pourable lubricating process, used through mandrel and also by brush. Good for ferrous and non-ferrous materials.
- Viscous non-dripping gel (16000 cSt at 20°C)
- Activated by heat released by drawing process
Good for steel, stainless steel, aluminium. Easy water clean-up.
ALTO 100


Grease is suitable for extreme duty bending processes and deep drawing. Eventually there is ability to be diluted with water further. Best practive to apply externally or internally by pump with compression ratio 50:1
- 1D bends
- Viscosity 250 000 cSt at 20°C
Suitable for ferrous and non-ferrous materials and high-alloyed steels.
FoxCut 1SF


Highly effective synthetic metalworking coolant. Easily miscible with water, usually in a ratio of 1:15-30. It does not contain additives based on chlorine, formaldehyde and paraffin. Completey non-hazardous in terms of safety of worker and environment. Cutting fluid transfers heat from the cut increases the cutting quality and prolongs tool life. Foxcut also prevents microbial growth and corrosion.
- Synthetic coolant
- Soluble with water
Perfect choice for high-speed operations. Foxcut prevents microbial attack and corrosion.
FoxCut 1HR


Highly effective synthetic metalworking coolant. Easily miscible with water, usually in a ratio of 1:15-30. It does not contain additives based on chlorine, formaldehyde and paraffin. Completey non-hazardous in terms of safety of worker and environment. Cutting fluid transfers heat from the cut increases the cutting quality and prolongs tool life. Foxcut also prevents microbial growth and corrosion.
- 100% Oil-free coolant
- Soluble with water
Perfect choice for high-speed operations. Foxcut prevents microbial attack and corrosion.
BBL Spray


Refillable spray
- Reduce spillage by using brush or roller
- Direct application with minimum waste
Pressurized air spray can